As a key control component in industrial piping systems, stainless steel flange gate valves play an important role in ensuring the normality of fluid transmission and system efficiency with their desi ...
Flanged Ball Valve, following a series of specifications and standards, is a type of valve widely used in the global industrial field. Its design is strictly in accordance with ANSI standards, ensurin ...
The electric high-platform three-piece ball valve is in a pre-tightening state between the ball and the plastic sealing rings on the left and right sealing seats. When the medium at the inlet and outl ...
Difference between plug valve and pneumatic three-piece ball valve Pneumatic three-piece ball valve and plug valve are valves of the same type, except that its closing piece is a sphere, which rotates ...
The name and function of each department, in the water inlet method of 1 Piece Ball Valve, meet the requirements of the water inlet ball valve. Position-related entry into the three-way side port, som ...
The control of the three-piece ball valve will make the pipeline run better In order to understand the direction of the pipeline, measure the terrain undulations along the pipeline and the length of t ...
We all know that when overhead pipelines are installed on the ground, the center line of the pipeline must be determined first. In addition, the center line, elevation, verticality, and matching degre ...
The three-piece ball valve is equipped with a multi-turn electric actuator, which can achieve the regulation and strict shutoff of the medium. It can be widely used in petroleum, chemical industry, ur ...
1 Piece Ball Valve analysis of local losses of sudden expansion pipe fittings of control pipelines. Since the speed of the outside is lower than that of the inside when the fluid flows through the pip ...
Stainless steel three-piece ball valve must have good sealing performance 3 Piece Ball Valve to control the hot air duct, it must have good sealing performance, because the hot air furnace is a high-t ...
The line connecting the two plumb balls is the direction line of the pipeline controlled by the stainless steel two-piece ball valve Before we measure the jacking pipe, we should first dig a jacking w ...
Method for determining the cross-sectional direction of a pipeline controlled by a stainless steel one-piece ball valve: First, we need to know that the measured width of the pipeline cross section is ...
The differences between 1 Piece Ball Valve and two-piece ball valves are as follows: 1. Disassembly difference: One-piece ball valve is a Cantonese ball valve, and two-piece ball valve is easier to di ...
Installation steps of 1 Piece Ball Valve 1. Before installing the one-piece ball valve, you need to clean the impurities in the pipeline, and then check whether there are foreign objects in the valve ...
The stainless steel three-piece ball valve is a valve that has been widely used in recent years. It is a relatively new type of ball valve. It has some advantages unique to its own structure, such as ...
The method of measuring the pipeline project controlled by 2 Piece Ball Valve is as follows: 1. Survey the topographic map, survey the pipeline area topographic map or draw a strip topographic map alo ...
The casting process of stainless steel three-piece ball valve is as follows: The casting of stainless steel three-piece ball valve body adopts advanced technology introduced from Taiwan, with reasonab ...
After a period of use, some impurities tend to accumulate inside the valve. Especially in some pipelines where the medium is a mixture of solid and liquid or the medium has high viscosity, the accumul ...
The nameplate of the three-piece ball valve shows the operating pressure allowed by the ball valve at the maximum and minimum operating temperatures. Using PTFE or RTFE valve seats and seals, the oper ...
1 Piece Ball Valve and Cantonese ball valves are both valve types we often mention, but these two ball valves are actually the same, just with different names. The driving methods of one-piece ball va ...
The opening and closing principle of the two-piece ball valve is as follows: I. When opening 1. At this time, the two-piece ball valve is in a closed state, and the ball is pressed tightly against the ...
The advantages of three-piece ball valves are as follows: 1. The three-piece ball valve has excellent sealing performance and is also used in vacuum systems. 2. The three-piece ball valve is easy to o ...
3 Piece Ball Valve adopts three connection methods: flange, internal thread and butt welding. It has reliable sealing and convenient maintenance. It is widely used in various industries. Its parameter ...
Differentiate from the structure: 1 Piece Ball Valve is an integrated valve, which consists of a ball, a PTFE ring, and a locking nut. The diameter of the ball is slightly smaller than the diameter of ...
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.
